Posted on: May 11, 2020 Posted by: admin Comments: 0


IRFP Transistor Datasheet, IRFP Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. Fifth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per. THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT IRFP SiHFP ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless.

Author: Akijind Volmaran
Country: Germany
Language: English (Spanish)
Genre: Video
Published (Last): 14 May 2014
Pages: 211
PDF File Size: 1.69 Mb
ePub File Size: 4.54 Mb
ISBN: 300-1-65191-797-7
Downloads: 28394
Price: Free* [*Free Regsitration Required]
Uploader: Tygokinos

IRFP150 MOSFET N-Channel

What will happen if you apply V on 0. Sign up using Email and Password.

Or it could mean 10 amps at 16 volts or 16 amps at 10 volts etc. Email Required, but never shown.

(PDF) IRFP150 Datasheet download

You always answer my questions in a very helpful and informative way. It’s easy to get into the habit of skipping over the last pages in a datasheet with iirfp150 and packaging information, it’s understandable that you missed it.

I don’t know where drain, source and gate are. If there’s missing data, the datasheet doesn’t contain it. If your catasheet was 10 ms then you could withstand volts whilst taking no more than about 2. When Vgs is high enough, then it will enter ohmic mode and meet its RdsON spec. The most important rule about any data sheet is this: Breakdown maximum Vds applies in all modes.


I’ve learned from you a lot of information. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. Thank you very much teacher Andy aka. The X axis is voltage and you can datashee it is limited to volts.

See “Source-Drain Ratings and Characteristics” for numbers on page 2. Data sheets are marketing. See also this on the last page: Post as a guest Name. That’s an instantaneous power of 8.

Is It V too? Eventually if the graph showed this detail you would find that the continuous power rating of watts means a continuous current of 1.

When the FET is fully on, it behaves more or less like a resistor of value RdsON, which is 36 mOhm in this case, so there would be no way to have volts across it. Chupacabras 3, 2 11 Yes, it is complete. However, if you apply Vds, and slowly raise Vgs from zero, at some point in will start to conduct and behave like a current source.

Sign up or log in Sign up using Google. Sign up using Facebook. That’s an instantaneous power of 9 kW.


Michael George 1, 8 34 This is the datasheet of a mosfet and I have two issues: Some prefer to call this “linear mode”, since this is the mode to use when you want to make a linear amplifier or a source follower with the FET. Thank you very much. The current would be amperes. The Vdss voltage is the voltage which the current starts to flow through fet. Also, both instant and average dissipation are limited see SOA graphs which will give you a time- and Vds-dependent current limit if you don’t want to fry it.


And power dissipation kW. This is called “saturation” for a MOSFET, which always ties my brain into knots, since “saturation” for a bipolar is at the other end of the characteristic. Notice now that the power taken during this much longer pulse is only watts.

IRFP Datasheet(PDF) – Vishay Siliconix

Which pin is gate and which is drain? By using our site, you acknowledge that you have read and understand our Cookie PolicyDatasheet Policyand our Terms of Service. As for the pinout, you can bet on the standard one, ie GDS. You have to consider allowed power dissipation and maximum current too. What this tells you is that if you could turn on and off the MOSFET in 10 us you could take amps but with a limited voltage orfp150 about 60 volts.


Leave a Comment