Posted on: October 23, 2020 Posted by: admin Comments: 0

ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Faerisar Dunos
Country: Mauritius
Language: English (Spanish)
Genre: Photos
Published (Last): 12 February 2008
Pages: 148
PDF File Size: 10.36 Mb
ePub File Size: 3.99 Mb
ISBN: 404-3-16559-689-3
Downloads: 36670
Price: Free* [*Free Regsitration Required]
Uploader: Malale

The change in weight of the specimens is to be calculated as astmm expression of percentage change on the original weight. The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer. Summary of Test Methods 3. Take a sufficient number of readings, depending on the size of the specimen, to provide a reliable average value.

ASTM F – 04 Standard Test Methods for Fluid Resistance of Gasket Materials

The sstm should be aware that results may differ. Please copy and paste this embed script to where you want to embed Embed Script. Use enough fluid to provide a minimum of 10 mL for each specimen in the container. BoxTrenton, NJ Dead weight loads are listed in Table 1. These test methods are applicable to ethylene glycol, propylene f46, commercial coolants and blends with water thereof see Note 1water, and other commercial oils and fuels.

  BUDIDAYA KEMANGI PDF

ASTM F146 – 12

Measure the weight of the test specimen to the nearest 1 mg 0. D146 to Test Method D for further information regarding immersion test fluids. The anvil shall have a diameter not less than that of the presser foot, which has a diameter of 6.

The producer must be aware that different coolant mixtures may yield different results. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. If such information is not available, then the material should be tested by itself in fresh fluid to determine compatibility with said fluid. Temperature of Test Measurement 7. Use the same sinker throughout.

It atm the responsibility of the user of this standard to establish appropriate asgm and health practices and determine the applicability of regulatory limitations prior to use. Then withdraw the specimens from the cooled-down test fluid and immediately blot the samples with sheets of blotting paper to remove excess liquid from the surfaces.

Please fill this form, we will try to respond as soon as possible. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. A number in parentheses indicates the year of last reapproval.

  DBMS IVAN BAYROSS PDF

There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and thickness change in IRM oil. The change in thickness of the specimens is to be calculated as an expression of percentage change from the original thickness.

ASTM F – 12 – Standard Test Methods for Fluid Resistance of Gasket Materials

The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. Change the distilled water used in the test frequently. Thank you for interesting in our services.

Graduate the dial in 0. We are a non-profit group that run this website to share documents. Current edition approved April 1, Your comments will receive careful consideration at a meeting of qstm responsible technical committee, which you may attend.

This standard has been approved for use by agencies of the Department of Defense. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Significance and Use 4. For materials having less than specific gravity 1. Size px x x x x Please help us to share our service with your friends.

Categories:

Leave a Comment