Posted on: May 22, 2020 Posted by: admin Comments: 0

2N2219A DATASHEET PDF

2NA Transistor Datasheet pdf, 2NA Equivalent. Parameters and Characteristics. DESCRIPTION. The 2NA and 2NA are silicon Planar. Epitaxial NPN transistors in Jedec TO (for. 2NA) and in Jedec TO (for 2NA). DESCRIPTION. SYMBOL. 2NA. UNIT. Collector -Emitter Voltage. VCEO. V. Collector . Data sheet specifications and its information contained are.

Author: Jugis Fegrel
Country: Iran
Language: English (Spanish)
Genre: Science
Published (Last): 11 November 2008
Pages: 129
PDF File Size: 20.64 Mb
ePub File Size: 1.70 Mb
ISBN: 323-8-98823-401-3
Downloads: 1210
Price: Free* [*Free Regsitration Required]
Uploader: Dizuru

As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. Amplifier modules like Audio 2n22219a, signal Amplifier etc. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

In our case for a collector current of mA we have to pass a base current of 16mA. Current flows in through collector, normally connected to load. To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. So to calculate the resistor value of the base we can use the formulae.

Current Drains out through emitter, normally connected to ground. 2n221a9 this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

  A HISTORY OF BYZANTINE MUSIC AND HYMNOGRAPHY PDF

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.

Where h FE, is the current gain of the transistor which in our case is So the value if R B will be. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: To bias a transistor we have to supply current to base pin, this current I Dataxheet should be limited to 5mA by using a transistor to the base pin.

2NA Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

Where Datqsheet is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. Submitted by admin on 21 June When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

This resistor is connected to the base pin of the transistor to limit the current flowing through the base. dafasheet

  BS 5628-3 PDF

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

2N2219A Datasheet, Equivalent, Cross Reference Search

Here lets us assume the load here consumes around mA maximum so our collector current I C mA. But this calculation will lead to the closest value to start with.

This stage is called Saturation Region. TL — Programmable Reference Voltage. Another important thing to keep in mind, while using a transistor as switch is the base resistor. So if you 2n22119a for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

The 2N is a NPN transistor and is normally used as a switch in many circuits.

Complete Technical Details can be found at the datasheet given at the end of this page. The value of this current can be calculated by the required amount of current that will be consumed by the load.

Categories:

Leave a Comment